Changes

Line 222: Line 222:     
* Place your fabric on the part that has been printed.
 
* Place your fabric on the part that has been printed.
[[File: Taped fabric.png|center|200x500 px|Taped fabric]]
+
[[File: Taped fabric.png|center|200x500 px|Taped fabric|link=Special:FilePath/Taped_fabric.png]]
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 9. Taped fabric</div>
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 9. Taped fabric</div>
   Line 236: Line 236:  
*Measure the amount of fabric you would need
 
*Measure the amount of fabric you would need
 
*We will use the laser cutter to cut out the fabric, you can use Inkscape to make the perforations.
 
*We will use the laser cutter to cut out the fabric, you can use Inkscape to make the perforations.
[[File: Perforations.png|center|200x500 px| Perforations]]
+
[[File: Perforations.png|center|200x500 px| Perforations|link=Special:FilePath/Perforations.png]]
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 10. Perforations Inkscape design </div>
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 10. Perforations Inkscape design </div>
   Line 242: Line 242:  
* Iron your fabric and lay it on a piece of MDF. Tape it securely into place.
 
* Iron your fabric and lay it on a piece of MDF. Tape it securely into place.
   −
[[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter]]
+
[[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter|link=Special:FilePath/Fabric_on_board_in_laser_cutter.png]]
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div>
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div>
    
* Configure the properties as follows:
 
* Configure the properties as follows:
  Note: Laser Cutter used: Epilog Mini
+
Note: Laser Cutter used: Epilog Mini
  The properties depend on the fabric used:
+
 
  Vector Settings:
+
The properties depend on the fabric used:
  Speed: 100 %
+
 
  Power: 10 %
+
Vector Settings:
  Frequency: 150 Hz
+
 
 +
* Speed: 100 %
 +
* Power: 10 %
 +
* Frequency: 150 Hz
    
*Begin cut:
 
*Begin cut:
[[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter]]
+
[[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter|link=Special:FilePath/Fabric_on_board_in_laser_cutter.png]]
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div>
 
<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div>
  
MakerRepo Staff, MakerRepo Volunteers
872

edits