Line 222: |
Line 222: |
| | | |
| * Place your fabric on the part that has been printed. | | * Place your fabric on the part that has been printed. |
− | [[File: Taped fabric.png|center|200x500 px|Taped fabric]] | + | [[File: Taped fabric.png|center|200x500 px|Taped fabric|link=Special:FilePath/Taped_fabric.png]] |
| <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 9. Taped fabric</div> | | <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 9. Taped fabric</div> |
| | | |
Line 236: |
Line 236: |
| *Measure the amount of fabric you would need | | *Measure the amount of fabric you would need |
| *We will use the laser cutter to cut out the fabric, you can use Inkscape to make the perforations. | | *We will use the laser cutter to cut out the fabric, you can use Inkscape to make the perforations. |
− | [[File: Perforations.png|center|200x500 px| Perforations]] | + | [[File: Perforations.png|center|200x500 px| Perforations|link=Special:FilePath/Perforations.png]] |
| <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 10. Perforations Inkscape design </div> | | <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 10. Perforations Inkscape design </div> |
| | | |
Line 242: |
Line 242: |
| * Iron your fabric and lay it on a piece of MDF. Tape it securely into place. | | * Iron your fabric and lay it on a piece of MDF. Tape it securely into place. |
| | | |
− | [[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter]] | + | [[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter|link=Special:FilePath/Fabric_on_board_in_laser_cutter.png]] |
| <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div> | | <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div> |
| | | |
| * Configure the properties as follows: | | * Configure the properties as follows: |
− | Note: Laser Cutter used: Epilog Mini
| + | Note: Laser Cutter used: Epilog Mini |
− | The properties depend on the fabric used:
| + | |
− | Vector Settings:
| + | The properties depend on the fabric used: |
− | Speed: 100 %
| + | |
− | Power: 10 %
| + | Vector Settings: |
− | Frequency: 150 Hz
| + | |
| + | * Speed: 100 % |
| + | * Power: 10 % |
| + | * Frequency: 150 Hz |
| | | |
| *Begin cut: | | *Begin cut: |
− | [[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter]] | + | [[File: Fabric on board in laser cutter.png|center|200x500 px| Fabric on board in laser cutter|link=Special:FilePath/Fabric_on_board_in_laser_cutter.png]] |
| <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div> | | <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">Figure 11. Fabric on board in laser cutter </div> |
| | | |