MakerRepo Staff, MakerRepo Volunteers
532
edits
Changes
Jump to navigation
Jump to search
Line 205:
Line 205: − + − + − + Line 219:
Line 219: + − + + Line 233:
Line 235: + + − + − + − + − + + +
→13. Click on [close].
=== 13. '''Click''' on [close]. ===
=== 13. '''Click''' on [close]. ===
14.To generate the toolpath, c'''lick''' on [Toolpath] → [Technology dialog…]
14.To generate the toolpath, '''click''' on [Toolpath] → [Technology dialog…]
The following dialog will display.
The following dialog will display.
[[File:Technology dialog display.png|border|center|500x350px|Technology dialog display]]
Figure 17. Technology dialog display
Figure 17. Technology dialog display
# '''Click''' on the right arrow button in the group Isolate until the Isolation Method Partial rubout is displayed.
# '''Click''' on the right arrow button in the group Isolate until the Isolation Method Partial rubout is displayed.
[[File:Technology dialog display with isolate group.png|border|center|500x350px|Technology dialog display with isolate group]]
Figure 18. Technology dialog display with isolate group
Figure 18. Technology dialog display with isolate group
[[File:Technology dialog display with pockets group .png|border|center|500x350px|Technology dialog display with pockets group]]
Figure 19. Technology dialog display with pockets group
Figure 19. Technology dialog display with pockets group
# '''Click''' on [Start]. The computation results and the tools required for the project are displayed. '''Check''' whether all required tools are available and placed in the machine. Steps to take if tools are missing are available below.
# '''Click''' on [Start]. The computation results and the tools required for the project are displayed. '''Check''' whether all required tools are available and placed in the machine. Steps to take if tools are missing are available below.
[[File: Computation results display for front PCB.png|border|center|500x350px|Computation results display for front PCB]]
Figure 20. Computation results display for front PCB
Figure 20. Computation results display for front PCB
[[File: Computation results display for back PCB.png|border|center|500x350px|Computation results display for back PCB]]
Figure 21. Computation results display for back PCB
Figure 21. Computation results display for back PCB
[[File: Front of PCB design with the toolpath generated .png|border|center|500x350px|Front of PCB design with the toolpath generated]]
Figure 22. Front of PCB design with the toolpath generated
Figure 22. Front of PCB design with the toolpath generated
[[File: Back of PCB design with the toolpath generated .png|border|center|500x350px| Back of PCB design with the toolpath generated]]
Figure 23. Back of PCB design with the toolpath generated
Figure 23. Back of PCB design with the toolpath generated
# If there are tools that are missing, '''Click''' on [Edit] → [Tool magazine…] The tools required for circuit board production are displayed. Tools that are missing in the tool magazine are marked with a red X.
# If there are tools that are missing, '''Click''' on [Edit] → [Tool magazine…] The tools required for circuit board production are displayed. Tools that are missing in the tool magazine are marked with a red X.
[[File: Tool magazine display.png|border|center|500x350px| Tool magazine display]]
Figure 24. Tool magazine display
Figure 24. Tool magazine display
# In the tool magazine, '''assign''' the required tools to the tool holder positions:
# In the tool magazine, '''assign''' the required tools to the tool holder positions:
[[File:Assigning tools in the correct tool holder position .png|border|center|500x350px|Assigning tools in the correct tool holder position]]
Figure 25. Assigning tools in the correct tool holder position
Figure 25. Assigning tools in the correct tool holder position
# Once all tools have been assigned successfully, '''Open''' the machine cover, and '''insert''' the tools into the tool holders of the tool magazine. Ensure that the tools are inserted into the tool holder positions that you have assigned in the dialog Tool magazine!
# Once all tools have been assigned successfully, '''Open''' the machine cover, and '''insert''' the tools into the tool holders of the tool magazine. Ensure that the tools are inserted into the tool holder positions that you have assigned in the dialog Tool magazine!
[[File:Insertion of tool into the tool holder.png|border|center|500x350px|Insertion of tool into the tool holder]]
Figure 26. Insertion of tool into the tool holder
Figure 26. Insertion of tool into the tool holder
[[File: Tool successfully inserted into the tool holder
.png|border|center|500x350px| Tool successfully inserted into the tool holder
]]
Figure 27. Tool successfully inserted into the tool holder
Figure 27. Tool successfully inserted into the tool holder