Difference between revisions of "Digital technologies/Laser cutting/Laser cutting- Beginner/How to Laser Cut in the Makerspace/Zing"

From CEED Wiki
Jump to navigation Jump to search
Line 130: Line 130:
 
*Remove the vector grid from the laser cutter.
 
*Remove the vector grid from the laser cutter.
 
*Loosen the green thumb crews to remove the front plate.
 
*Loosen the green thumb crews to remove the front plate.
*Remove the debris
+
*Remove the debris and clean the tray.
 
*Fit the front plate back to the vector grid.
 
*Fit the front plate back to the vector grid.
 
*Place the vector grid back into the laser cutter, carefully aligning the three circles on the vector grid on the vector circles of the laser cutter.
 
*Place the vector grid back into the laser cutter, carefully aligning the three circles on the vector grid on the vector circles of the laser cutter.

Revision as of 19:32, 13 June 2024

Epilog Zing

The Epilog Zing[1] is a 40 W CO2 laser with the ability to cut through a variety of materials such as MDF (Medium-Density Fiberboard) and acrylic which are commonly used during laser cutting projects at the Makerspace. While the procedure to operate an Epilog Zing remains mostly similar to the steps taken to operate the Epilog Mini and the Epilog Helix, there exist some differences that should be taken into account when dealing with the Epilog Zing. For example, the Epilog Zing can be carried in the Maker Mobile and is found in the Maker Lab.

Epilog Zing
EpilogZing.png
Power Type [40W, CO2]
Build Volume (mm) 730 × 562 × 298 mm
Build Volume (in) 28.75 × 22.125 × 11.75 in
Compatible materials See charts below
Maximum Resolution 1000 dpi

The Maker Mobile

Makermobile Laser Cutter

The Maker Mobile is a makerspace on wheels. Most of the equipment that can be found in a makerspace, can be carried directly to schools, libraries and even birthday parties.  The Epilog Zing is one of the equipment that is carried on the Maker Mobile making it a portable machine. Apart from the laser cutter itself, there are other components that are required for its smooth operation. The elements are shown in the picture.

Laser Cutter Components

In order to use the Epilog Zing laser cutter, the 4 components that you need are:

  • The Laser Cutter: Machine that will cut the material.
  • Laptop: The laptop is used to upload the design that need to be cut to the laser. It is also used to configure all the necessary setting of the laser. Note that the operating system running on the laptop is Windows 7.
  • Air Filter: The filter should always be attached while performing a cut, the laser cutter is not to be used without the filter, this ensures that the air in the room is safe for users and limits potentially hazardous debris.
  • Air Compressor (compressed air): A steady flow of air to blow smoke and cutting residue away from the beam path and optics of a laser cutter. It's simple, but critical; without it, smoke can obscure and reflect the laser beam, foul lenses and mirrors, and severely degrade cut quality.

Control Panel[2]

Control Panel
Control Panel on Epilog Zing

One way for the user to interact with the laser is by using the control panel. The list below describes the properties of each button found in the laser cutter control panel.


  1. Go: Start or stop a job or process
  2. Pause: Stop a process. When rastering ,it will stop right away. When vectoring, it will only stop once it has finished its current path
  3. Reset(0): Move the head back to Home position.
  4. Speed(1): While rastering you can adjust the speed by pushing this button on and using the up(3) and down(4) arrow keys
  5. Power(2): While rastering you can adjust the power by pushing this button on and using the up(3) and down(4) arrow keys
  6. Focus(5): Press this button, then either the up or down button to raise or lower the bed. Using this process along with the focusing tool, you can focus the laser. Note, the focusing tool for the Epilog Zing is different from the other laser cutters, it is attached inside the machine itself and can move back and forth, hence showing the distance between it and the material to be cut.
  7. Job(6): Press this button to display the file name of the last job stored in memory. The arrow keys can also be used to scroll through all the saved jobs.
  8. Pointer(7): Turn on/off the red light pointer
  9. X/Y Off(8): Press this button to disable the X and Y motors and move the laser head around manually
  10. Config(9): Access to the calibration settings.
  11. Data: This light will illuminate when data is being passed to the laser, useful when checking if your computer is connected to the laser cutter.
  12. ∆/∇(3 and 4):Cycle through the jobs or raise or lower the power, speed, or bed height

Properties

The other way for the user to interact with the laser cutter is by setting up the laser properties for a cut.

Properties
  1. Resolution: The print resolution can set from 100 to 1000 Dots per inch (DPI), the higher the DPI the more time it takes for laser cutter to complete the job. Usually, the print resolution is set at 500 DPI, the settings on the laptop will demonstrate the same.
  2. Centre Engraving: It allows you to define the centre of the job.
  3. Job Manager Features[2]:You can choose to print to either the printer (your laser), the Job Manager, or both. This allows you to send your job to the Job Manager without sending it to the laser so you can then print the job directly from the Job Manager at a later time without accessing your graphic software. You can leave the two boxes ticked.
  4. Job type
    • Raster: Used for engraving material. Vector lines that should be engraved should be set to 0.006” (0.152 mm) or greater line thickness.
    • Vector: Select when running cuts only. Vector lines that should be cut have to be set to  0.001” (0.0254 mm) or else it won’t recognized as cut.  
    • Combined: Select when running both cutting and engraving.
  5. Piece size: Enter the size of the document of the job.
  6. Raster Settings:
    • Speed: Determines the travel speed of the laser. It can be increased increments of 1%. The lower the speed, the deeper the cut. Each materials have their own specific value and can be in “Suggested Material settings” which is located on the table, next to the laser cutter.
    • Power: Determines the amount of laser energy that is delivered to the piece being cut/engraved and is adjustable in 1% increments. Each materials have their own specific value and can be in “Suggested Material settings” which is located on the table, next to the laser cutter.
  7. Vector Settings:
    • Speed: Determines the travel speed of the laser. It can be increased increments of 1%. The lower the speed, the deeper the cut. Each materials have their own specific value and can be in “Suggested Material settings” which is located on the table, next to the laser cutter.
    • Power: Determines the amount of laser energy that is delivered to the piece being cut/engraved and is adjustable in 1% increments. Each materials have their own specific value and can be in “Suggested Material settings” which is located on the table, next to the laser cutter.
    • Frequency: Determines the number of laser pulses per inch of cut. Lower frequency means less heat is being applied to the material. The frequency can range between 1 to 5000 Hz. Each materials have their own specific value and can be in “Suggested Material settings” which is located on the table, next to the laser cutter.

How to Laser cut?

The laser cutting process with the Epilog Zing is as follows:

  1. Prepare your file and select your material
  2. Move your file to the laser cutter computer (you may use the USB key connected to the laptop or you can find one at the Makerspace)
  3. Turn on laser cutter setup
  4. Prepare laser cutter
  5. Click print and select print settings
  6. Start the cut
  7. Turn off laser cutter setup
  8. Clean up

Prepare your file and select your material

Before you are going to start laser cutting, you need to get some prep work out of the way. First you need to create or select your file. If you are rastering an image, you can select or create an image in any program or use an existing picture. If you are rastering an image, you can select or create an image in any program or use an existing picture.

If you want to add vector cuts, you need to use a program that has the ability to create vectors. We use a free program called Inkscape. A guide on how to use the program can be found here. Unfortunately, you can’t print directly from Inkscape, you need to simply save your file as .pdf.

Move file to the laser cutter laptop

Once you have saved your file as a .pdf, move it to a USB drive and bring it over to the laser cutter laptop. Open your file on the laptop.

Turn on the laser cutter

There are three items to turn on:

Air Filter
Air Compressor
  • Laser cutter: Switch on right hand side at the back. When you turn on the laser cutter, let the head move around freely. Refrain from touching any other buttons until it has finished this process.
  • Air filter: Power button at bottom front.
  • Air compressor: Switch Located on top right on the machine's side.

Prepare the laser cutter

The laser cutter needs to be adapted to the material and image you are going to cut. This is done by changing the height and the laser’s home. The height affects the laser’s focus, and the home is related to the center engraving. More information about this can be found on the laser settings page.

  • Setting home: This is setting the origin for the laser. If you do not have center engraving, select. This will be the top left-hand corner of the piece. For more information, see the laser setting page.
    1. Make sure the laser cutter is on.
    2. Press the pointer button. You should see a red dot under the laser head. That is the current location of the laser.
    3. Press X/Y off. You should be able to freely move the laser cutter head.
    4. Move the laser head so that the red dot is at the desired origin.
    5. Press on Go to set home, you should not be able to move the laser cutter head.
Focusing Tool
  • Focusing laser:
    1. Make sure the laser is on.
    2. Place the material on the laser bed. You want to make sure that the area you are cutting is parallel to laser bed and the track on which the laser head moves. If there is a variation in height, you will see a variation in properties of the rastering and vectoring done by the laser
    3. Use the focusing tool present inside the laser cutter.
    4. Press the Focus button on the laser cutter control panel. The laser head will move over slightly, make sure that the material is still under the manual focus.
    5. Using the up and down arrows, lower or raise the bed until the manual focus guide is resting on the material without being lifted off the base. Try to swing the focusing tool back and forth. If the tool doesn't move freely after its first swing, that is, it returns to its original position, the laser has been correctly focused.

Click print and select settings

On the computer, click print. The print setup window will appear.

  1. Change the printer to the laser cutter you are going to be using.
  2. Click on properties. This will bring up a page on the laser cutter settings. Consult the laser cutter manual for the proper speed and vector settings. More information on settings can be found on the Laser Settings page. When you are done selecting all your settings, click ok. This will take you back to the print page.
  3. Make sure that the picture is set to Actual size. If it is set to fit the vector lines will most likely not work.
  4. Select orientation, either auto, portrait, or landscape. Most of the time, this will be set to auto portrait/landscape. This means that the laser will look at the size of the image you are attempting to cut and the size that you have added in the properties page. It will attempt to place the image in the way that it will fit best. If you want your image in a specific direction, select either portrait or landscape.

When all settings are chosen, click print. If you look over to the laser cutter the name of the file should appear on the control panel. Wait until the data light is no longer flashing.

Start cut

  1. Make sure that the glass cover is down and that you have prepared the laser. Check that your job is set on the display of the laser cutter.
  2. Press the green button, Go.
  3. While the laser cutter is cutting, do not leave the laser cutter unattended. If small flames appear, do not panic. As long as you piece is not actively burning, you are ok. If at any point you are unsure, pause your cut and find the Makerspace Coordinator on duty. You can pause your cut by pressing the red button, Stop, it will always finish the line that is cutting before it ends. If it needs to be stopped for safety purposes and it is not stopping with the Red Button, use the On/Off switch on the left side of the laser. Leave the lid closed. To resume, press the green button, Go.

Turn off laser cutter setup

When you are finished all your cuts, turn off the laser cutter, the air compressor, the air filter and disconnect the extension cord from the electrical outlet.

Clean up[2]

Vector grid

So that our laser remains operational, it is important that we clean up after each cut.

  • Remove the vector grid from the laser cutter.
  • Loosen the green thumb crews to remove the front plate.
  • Remove the debris and clean the tray.
  • Fit the front plate back to the vector grid.
  • Place the vector grid back into the laser cutter, carefully aligning the three circles on the vector grid on the vector circles of the laser cutter.

Laser Safety

Before any laser cutting is done, you should ensure that the air filter and the air compressor are both switched on apart from the laser cutter itself. Refer to this video for other safety guidelines.

Troubleshooting Laser Cutter Issues

  1. File not sending to the Laser Cutter
    • Try unplugging the USB Cable from the laser and plugging it back, the files should now be available on the Laser Screen
    • Make sure to choose the Printer that has a "USB" at the end of the printer's name in Adobe Acrobat Reader
    • Try turning the laser Off and On.
  2. Vector not working: When sending a vector file, if the Laser Cutter makes a sound right away and doesn't start, it means something is probably wrong with the file.
    • Make sure the line thickness is actually 0.001 inch.
    • Make sure opacity is at exactly 100%.
    • Make sure that the Vector or Combined setting in the Epilog Driver is selected.
    • Try opening the file back in Inkscape or your preferred vector software and make sure the lines are a solid color
  3. Laser starts shifting on the side
    • Stop the print and make sure the size doesn't exceed the size of the laser's bed (Zing 16"x12")
    • Ask the staff to check the laser, but this issue will probably mean that the laser needs to go 'Out of Order' for maintenance
  4. Only part of the file gets printed
    • Check your canvas size is the actual size or bigger that everything that is in that document
    • Make sure that in the Epilog Driver, the "Piece size" is bigger than the size of your document


Resources

  • Laser Safety
  • Material Settings: If a material is unlisted in the allowed materials list, please consult a Makerspace employee for further guidance.
  • Makerbox:Makerbox is a web-based case generator for laser cutting. It allows for the creation of boxes with live hinges at the corners. Unfortunately, it only outputs .DXF or .DWG file formats and does not support the export of 3D CAD models for modifications in a 3D CAD software.
  • Epilog Zing Manual

References