Difference between revisions of "Ultimaker 2+"
m |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | |||
{{PrinterInfobox | {{PrinterInfobox | ||
| name = Ultimaker 2+ | | name = Ultimaker 2+ | ||
| Line 4: | Line 5: | ||
| slicerName = Cura | | slicerName = Cura | ||
| slicerLink = https://ultimaker.com/cura | | slicerLink = https://ultimaker.com/cura | ||
| − | | materials =PLA, ABS, Flexible | + | | materials = PLA, ABS, Flexible |
| − | | minLayerHeight =0.06 | + | | minLayerHeight = 0.06 |
| − | | heatedBuildPlate =Yes | + | | heatedBuildPlate = Yes |
| − | |float=right|buildWidth=223|buildDepth=223|buildHeight=205|recommendedSettings=https://en.wiki.makerepo.com/wiki/Ultimaker_2%2B}} | + | | float = right |
| + | | moreInformation = https://en.wiki.makerepo.com/wiki/Ultimaker_2%2B | ||
| + | | buildWidth = 223 | ||
| + | | buildDepth = 223 | ||
| + | | buildHeight = 205 | ||
| + | | recommendedSettings = https://en.wiki.makerepo.com/wiki/Ultimaker_2%2B | ||
| + | }} | ||
| + | == Recommended Settings == | ||
These are the presets for the different nozzles on the Ultimaker 2+. | These are the presets for the different nozzles on the Ultimaker 2+. | ||
| Line 94: | Line 102: | ||
|120 | |120 | ||
|} | |} | ||
| + | |||
| + | == Staring the print == | ||
| + | To start a print on the Ultimaker 2+ you will first need an SD card to upload your files to the printer. These can be requested from the front desk after you sign out a printer. For the Ultimaker 2+ the slicer to use is Cura. Once you have your model sliced in Cura, insert the SD card into your computer. This should add the option to "save to removable disk" ad the bottom left of Cura. Once your file is on the SD card go to the printer and insert the card. If the machine is on, rotate the dial until "print" is highlighted, then push the dial in. This will open the SD card and from this menu you can choose your file. To chose, press the dial in again and the printer will heat up and start printing. | ||
[[Category:3D Printers]] | [[Category:3D Printers]] | ||
Latest revision as of 19:52, 4 June 2024
| Slicer | Cura |
|---|---|
| Build Volume | 223 × 223 × 205 mm |
| Compatible materials | PLA, ABS, Flexible |
| Minimum Layer Height | 0.06 mm |
| Heated Build Plate | Yes |
| More Information | Ultimaker 2+ |
Recommended Settings
These are the presets for the different nozzles on the Ultimaker 2+.
Using 0.4 nozzle
| Low print | Normal | High | |
| Layer Height (mm) | 0.15 | 0.10 | 0.06 |
| Top/Bottom Layer thickness (mm) | 0.75 | 1.05 | 1.05 |
| Wall thickness (mm) | 0.7 | 0.8 | 0.72 |
| Infill (%) | 18 | 20 | 22 |
| Build Speed (mm/s) | 60 | 50 | 50 |
| Travel Speed (mm/s) | 150 | 120 | 120 |
Using 0.6 Nozzle
| Normal | |
| Layer Height (mm) | 0.15 |
| Top/Bottom Layer thickness (mm) | 1.2 |
| Wall thickness (mm) | 1.59 |
| Infill (%) | 20 |
| Build Speed (mm/s) | 55 |
| Travel Speed (mm/s) | 120 |
Using 0.8 Nozzle
| Low | |
| Layer Height (mm) | 0.2 |
| Top/Bottom Layer thickness (mm) | 1.2 |
| Wall thickness (mm) | 2.1 |
| Infill (%) | 20 |
| Build Speed (mm/s) | 40 |
| Travel Speed (mm/s) | 120 |
Staring the print
To start a print on the Ultimaker 2+ you will first need an SD card to upload your files to the printer. These can be requested from the front desk after you sign out a printer. For the Ultimaker 2+ the slicer to use is Cura. Once you have your model sliced in Cura, insert the SD card into your computer. This should add the option to "save to removable disk" ad the bottom left of Cura. Once your file is on the SD card go to the printer and insert the card. If the machine is on, rotate the dial until "print" is highlighted, then push the dial in. This will open the SD card and from this menu you can choose your file. To chose, press the dial in again and the printer will heat up and start printing.