Difference between revisions of "Raise3D N2 Plus"
Jump to navigation
Jump to search
| (One intermediate revision by the same user not shown) | |||
| Line 8: | Line 8: | ||
| minLayerHeight = 0.01 | | minLayerHeight = 0.01 | ||
| heatedBuildPlate = Yes | | heatedBuildPlate = Yes | ||
| − | |float=right | + | | float = right |
| − | |buildWidth=305 | + | | moreInformation = https://en.wiki.makerepo.com/wiki/Raise3D_N2_Plus |
| − | |buildDepth=305 | + | | buildWidth = 305 |
| − | |buildHeight=605 | + | | buildDepth = 305 |
| − | |recommendedSettings=https://en.wiki.makerepo.com/wiki/Raise3D_N2_Plus}} | + | | buildHeight = 605 |
| + | | recommendedSettings = https://en.wiki.makerepo.com/wiki/Raise3D_N2_Plus | ||
| + | }} | ||
| − | + | ==Recommended settings== | |
| + | {| class="wikitable" | ||
| + | | | ||
| + | |Low print | ||
| + | |Normal | ||
| + | |High | ||
| + | |- | ||
| + | |Layer Height (mm) | ||
| + | |0.15 | ||
| + | |0.10 | ||
| + | |0.06 | ||
| + | |- | ||
| + | |Top/Bottom Layer thickness (mm) | ||
| + | |0.75 | ||
| + | |1.05 | ||
| + | |1.05 | ||
| + | |- | ||
| + | |Wall thickness (mm) | ||
| + | |0.7 | ||
| + | |0.8 | ||
| + | |0.72 | ||
| + | |- | ||
| + | |Infill (%) | ||
| + | |18 | ||
| + | |20 | ||
| + | |22 | ||
| + | |- | ||
| + | |Build Speed (mm/s) | ||
| + | |60 | ||
| + | |50 | ||
| + | |50 | ||
| + | |- | ||
| + | |Travel Speed (mm/s) | ||
| + | |150 | ||
| + | |120 | ||
| + | |120 | ||
| + | |} | ||
| + | |||
| + | == Staring the print == | ||
| + | To start a print on the Raise N2 Plus, your file must first be sliced in a slicer called ideaMaker. Once sliced the file must be saved on a USB stick and inserted into the side of the machine. Then a password must be entered before you can continue. Please ask a staff member for help. Finally select print and navigate the folders for your file and select print. the machine will then heat up and start printing. | ||
[[Category:3D Printers]] | [[Category:3D Printers]] | ||
Latest revision as of 18:52, 4 June 2024
Raise3D N2 Plus
| Slicer | ideaMaker |
|---|---|
| Build Volume | 305 × 305 × 605 mm |
| Compatible materials | PLA, ABS, PVA, Flexible |
| Minimum Layer Height | 0.01 mm |
| Heated Build Plate | Yes |
| More Information | Raise3D N2 Plus |
Recommended settings
| Low print | Normal | High | |
| Layer Height (mm) | 0.15 | 0.10 | 0.06 |
| Top/Bottom Layer thickness (mm) | 0.75 | 1.05 | 1.05 |
| Wall thickness (mm) | 0.7 | 0.8 | 0.72 |
| Infill (%) | 18 | 20 | 22 |
| Build Speed (mm/s) | 60 | 50 | 50 |
| Travel Speed (mm/s) | 150 | 120 | 120 |
Staring the print
To start a print on the Raise N2 Plus, your file must first be sliced in a slicer called ideaMaker. Once sliced the file must be saved on a USB stick and inserted into the side of the machine. Then a password must be entered before you can continue. Please ask a staff member for help. Finally select print and navigate the folders for your file and select print. the machine will then heat up and start printing.